Wednesday, May 5, 2010


System architecture

As with all systems in the telecommunication area, GSM comes with a hierarchical,
complex system architecture comprising many entities, interfaces, and
acronyms. Figure 4.4 gives a simplified overview of the GSM system as specified
in ETSI (1991b). A GSM system consists of three subsystems, the radio sub
system (RSS), the network and switching subsystem (NSS), and the operation
subsystem (OSS). Each subsystem will be discussed in more detail in the following
sections. Generally, a GSM customer only notices a very small fraction of
the whole network – the mobile stations (MS) and some antenna masts of the
base transceiver stations (BTS).

Radio subsystem

As the name implies, the radio subsystem (RSS) comprises all radio specific
entities, i.e., the mobile stations (MS) and the base station subsystem (BSS).
Figure 4.4 shows the connection between the RSS and the NSS via the A interface
(solid lines) and the connection to the OSS via the O interface (dashed
lines). The A interface is typically based on circuit-switched PCM-30 systems
(2.048 Mbit/s), carrying up to 30 64 kbit/s connections, whereas the O interface
uses the Signalling System No. 7 (SS7) based on X.25 carrying management data
to/from the RSS.

Base station subsystem (BSS):

A GSM network comprises many BSSs, each
controlled by a base station controller (BSC). The BSS performs all functions
necessary to maintain radio connections to an MS, coding/decoding of
voice, and rate adaptation to/from the wireless network part. Besides a BSC,
the BSS contains several BTSs.

● Base transceiver station (BTS): A BTS comprises all radio equipment, i.e.,
antennas, signal processing, amplifiers necessary for radio transmission. A
BTS can form a radio cell or, using sectorized antennas, several cells (see section
2.8), and is connected to MS via the Um interface (ISDN U interface for
mobile use), and to the BSC via the Abis interface. The Um interface contains
all the mechanisms necessary for wireless transmission (TDMA, FDMA etc.)
and will be discussed in more detail below. The Abis interface consists of 16 or
64 kbit/s connections. A GSM cell can measure between some 100 m and
35 km depending on the environment (buildings, open space, mountains
etc.) but also expected traffic.

● Base station controller (BSC): The BSC basically manages the BTSs. It
reserves radio frequencies, handles the handover from one BTS to another
within the BSS, and performs paging of the MS. The BSC also multiplexes
the radio channels onto the fixed network connections at the A interface.

● Mobile station (MS): The MS comprises all user equipment and software
needed for communication with a GSM network. An MS consists of user
independent hard- and software and of the subscriber identity module
(SIM), which stores all user-specific data that is relevant to GSM. While an
MS can be identified via the international mobile equipment identity
(IMEI), a user can personalize any MS using his or her SIM, i.e., user-specific
mechanisms like charging and authentication are based on the SIM, not on
the device itself. Device-specific mechanisms, e.g., theft protection, use the
device specific IMEI. Without the SIM, only emergency calls are possible. The
SIM card contains many identifiers and tables, such as card-type, serial
number, a list of subscribed services, a personal identity number (PIN), a
PIN unblocking key (PUK), an authentication key Ki, and the international
mobile subscriber identity (IMSI) (ETSI, 1991c). The PIN is used to
unlock the MS. Using the wrong PIN three times will lock the SIM. In such
cases, the PUK is needed to unlock the SIM. The MS stores dynamic information
while logged onto the GSM system, such as, e.g., the cipher key Kc and
the location information consisting of a temporary mobile subscriber identity
(TMSI) and the location area identification (LAI). Typical MSs for GSM
900 have a transmit power of up to 2 W, whereas for GSM 1800 1 W is
enough due to the smaller cell size. Apart from the telephone interface, an
MS can also offer other types of interfaces to users with display, loudspeaker,
microphone, and programmable soft keys. Further interfaces comprise computer
modems, IrDA, or Bluetooth. Typical MSs, e.g., mobile phones,
comprise many more vendor-specific functions and components, such as
cameras, fingerprint sensors, calendars, address books, games, and Internet
browsers. Personal digital assistants (PDA) with mobile phone functions are
also available. The reader should be aware that an MS could also be integrated
into a car or be used for location tracking of a container.

Network and switching subsystem

The “heart” of the GSM system is formed by the network and switching subsystem
(NSS). The NSS connects the wireless network with standard public
networks, performs handovers between different BSSs, comprises functions for
worldwide localization of users and supports charging, accounting, and roaming
of users between different providers in different countries. The NSS consists of
the following switches and databases:

● Mobile services switching center (MSC): MSCs are high-performance digital
ISDN switches. They set up connections to other MSCs and to the BSCs
via the A interface, and form the fixed backbone network of a GSM system.
Typically, an MSC manages several BSCs in a geographical region. A gateway
MSC (GMSC) has additional connections to other fixed networks, such as
PSTN and ISDN. Using additional interworking functions (IWF), an MSC
can also connect to public data networks (PDN) such as X.25. An MSC
handles all signaling needed for connection setup, connection release and
handover of connections to other MSCs. The standard signaling system
No. 7 (SS7) is used for this purpose. SS7 covers all aspects of control signaling
for digital networks (reliable routing and delivery of control messages,
establishing and monitoring of calls). Features of SS7 are number portability,
free phone/toll/collect/credit calls, call forwarding, three-way calling etc. An
MSC also performs all functions needed for supplementary services such as
call forwarding, multi-party calls, reverse charging etc.

● Home location register (HLR): The HLR is the most important database in a
GSM system as it stores all user-relevant information. This comprises static
information, such as the mobile subscriber ISDN number (MSISDN), subscribed
services (e.g., call forwarding, roaming restrictions, GPRS), and the
international mobile subscriber identity (IMSI). Dynamic information is
also needed, e.g., the current location area (LA) of the MS, the mobile subscriber
roaming number (MSRN), the current VLR and MSC. As soon as an
MS leaves its current LA, the information in the HLR is updated. This information
is necessary to localize a user in the worldwide GSM network. All these
user-specific information elements only exist once for each user in a single
HLR, which also supports charging and accounting. The parameters will be
explained in more detail in section 4.1.5. HLRs can manage data for several
million customers and contain highly specialized data bases which must fulfill
certain real-time requirements to answer requests within certain time-bounds.

● Visitor location register (VLR): The VLR associated to each MSC is a
dynamic database which stores all important information needed for the
MS users currently in the LA that is associated to the MSC (e.g., IMSI,
MSISDN, HLR address). If a new MS comes into an LA the VLR is responsible
for, it copies all relevant information for this user from the HLR. This
hierarchy of VLR and HLR avoids frequent HLR updates and long-distance
signaling of user information. The typical use of HLR and VLR for user
localization will be described in section 4.1.5. Some VLRs in existence, are
capable of managing up to one million customers.

Operation subsystem

The third part of a GSM system, the operation subsystem (OSS), contains the
necessary functions for network operation and maintenance. The OSS possesses
network entities of its own and accesses other entities via SS7 signaling (see
Figure 4.4). The following entities have been defined:

● Operation and maintenance center (OMC): The OMC monitors and controls
all other network entities via the O interface (SS7 with X.25). Typical
OMC management functions are traffic monitoring, status reports of network
entities, subscriber and security management, or accounting and
billing. OMCs use the concept of telecommunication management network
(TMN) as standardized by the ITU-T.

● Authentication centre (AuC): As the radio interface and mobile stations
are particularly vulnerable, a separate AuC has been defined to protect user
identity and data transmission. The AuC contains the algorithms for
authentication as well as the keys for encryption and generates the values
needed for user authentication in the HLR. The AuC may, in fact, be situated
in a special protected part of the HLR.

● Equipment identity register (EIR): The EIR is a database for all IMEIs, i.e.,
it stores all device identifications registered for this network. As MSs are
mobile, they can be easily stolen. With a valid SIM, anyone could use the
stolen MS. The EIR has a blacklist of stolen (or locked) devices. In theory an
MS is useless as soon as the owner has reported a theft. Unfortunately, the
blacklists of different providers are not usually synchronized and the illegal
use of a device in another operator’s network is possible (the reader may
speculate as to why this is the case). The EIR also contains a list

No comments:

Post a Comment