Monday, May 3, 2010

GSM....

last post ws about evolution of these technologies....
nw letz discuss something about GSM system in particular.


GSM is the most successful digital mobile telecommunication system in the
world today. It is used by over 800 million people in more than 190 countries.
In the early 1980s, Europe had numerous coexisting analog mobile phone systems,
which were often based on similar standards (e.g., NMT 450), but ran on
slightly different carrier frequencies. To avoid this situation for a second generation
fully digital system, the groupe spéciale mobile (GSM) was founded in
1982. This system was soon named the global system for mobile communications
(GSM), with the specification process lying in the hands of ETSI (ETSI,
2002), (GSM Association, 2002). In the context of UMTS and the creation of
3GPP (Third generation partnership project, 3GPP, 2002a) the whole development
process of GSM was transferred to 3GPP and further development is
combined with 3G development. 3GPP assigned new numbers to all GSM stan-
96 Mobile communicationsdards. However, to remain consistent with most of the GSM literature, this GSM section stays with the original numbering (see 3GPP, 2002a, for conversion).
Section 4.4 will present the ongoing joint specification process in more detail.
The primary goal of GSM was to provide a mobile phone system that allows
users to roam throughout Europe and provides voice services compatible to
ISDN and other PSTN systems. The specification for the initial system already
covers more than 5,000 pages; new services, in particular data services, now add
even more specification details. Readers familiar with the ISDN reference model
will recognize many similar acronyms, reference points, and interfaces. GSM
standardization aims at adopting as much as possible.GSM is a typical second generation system, replacing the first generation analog systems, but not offering the high worldwide data rates that the third generation systems, such as UMTS, are promising. GSM has initially been deployed in
Europe using 890–915 MHz for uplinks and 935–960 MHz for downlinks – this
system is now also called GSM 900 to distinguish it from the later versions. These
versions comprise GSM at 1800 MHz (1710–1785 MHz uplink, 1805–1880 MHz
downlink), also called DCS (digital cellular system) 1800, and the GSM system
mainly used in the US at 1900 MHz (1850–1910 MHz uplink, 1930–1990 MHz
downlink), also called PCS (personal communications service) 1900. Two
more versions of GSM exist. GSM 400 is a proposal to deploy GSM at
450.4–457.6/478.8–486 MHz for uplinks and 460.4–467.6/488.8–496 MHz for
downlinks. This system could replace analog systems in sparsely populated areas.
A GSM system that has been introduced in several European countries for
railroad systems is GSM-Rail (GSM-R, 2002), (ETSI, 2002). This system does not
only use separate frequencies but offers many additional services which are
unavailable using the public GSM system. GSM-R offers 19 exclusive channels
for railroad operators for voice and data traffic (see section 4.1.3 for more information
about channels). Special features of this system are, e.g., emergency calls
with acknowledgements, voice group call service (VGCS), voice broadcast service
(VBS). These so-called advanced speech call items (ASCI) resemble features
typically available in trunked radio systems only (see section 4.3). Calls are prioritized:
high priority calls pre-empt low priority calls. Calls have very short
set-up times: emergency calls less than 2 s, group calls less than 5 s. Calls can be
directed for example, to all users at a certain location, all users with a certain
function, or all users within a certain number space. However, the most sophisticated
use of GSM-R is the control of trains, switches, gates, and signals. Trains
going not faster than 160 km/h can control all gates, switches, and signals
themselves. If the train goes faster than 160 km/h (many trains are already capable
of going faster than 300 km/h) GSM-R can still be used to maintain control.


Mobile services


GSM permits the integration of different voice and data services and the interworking
with existing networks. Services make a network interesting for
customers. GSM has defined three different categories of services: bearer, tele,
and supplementary services. These are described in the following subsections.
Figure 4.3 shows a reference model for GSM services. A mobile station MS is
connected to the GSM public land mobile network (PLMN) via the Um interface.
(GSM-PLMN is the infrastructure needed for the GSM network.) This
network is connected to transit networks, e.g., integrated services digital network
(ISDN) or traditional public switched telephone network (PSTN). There
might be an additional network, the source/destination network, before another
terminal TE is connected. Bearer services now comprise all services that enable
the transparent transmission of data between the interfaces to the network, i.e., S
in case of the mobile station, and a similar interface for the other terminal (e.g.,
S0 for ISDN terminals). Interfaces like U, S, and R in case of ISDN have not been
defined for all networks, so it depends on the specific network which interface is
used as a reference for the transparent transmission of data. In the classical GSM
model, bearer services are connection-oriented and circuit- or packet-switched.
These services only need the lower three layers of the ISO/OSI reference model.
Within the mobile station MS, the mobile termination (MT) performs all
network specific tasks (TDMA, FDMA, coding etc.) and offers an interface for
data transmission (S) to the terminal TE which can then be network independent.
Depending on the capabilities of TE, further interfaces may be needed,
such as R, according to the ISDN reference model (Halsall, 1996). Tele services
are application specific and may thus need all seven layers of the ISO/OSI reference
model. These services are specified end-to-end, i.e., from one terminal TE
to another.

Bearer services:

GSM specifies different mechanisms for data transmission, the original GSM
allowing for data rates of up to 9600 bit/s for non-voice services. Bearer services
permit transparent and non-transparent, synchronous or asynchronous data
transmission. Transparent bearer services only use the functions of the physical
layer (layer 1) to transmit data. Data transmission has a constant delay and
throughput if no transmission errors occur. The only mechanism to increase transmission quality is the use of forward error correction (FEC), which codes
redundancy into the data stream and helps to reconstruct the original data in
case of transmission errors. Depending on the FEC, data rates of 2.4, 4.8, or
9.6 kbit/s are possible. Transparent bearer services do not try to recover lost data
in case of, for example, shadowing or interruptions due to handover.
Non-transparent bearer services use protocols of layers two and three to
implement error correction and flow control. These services use the transparent
bearer services, adding a radio link protocol (RLP). This protocol comprises
mechanisms of high-level data link control (HDLC), (Halsall, 1996) and special
selective-reject mechanisms to trigger retransmission of erroneous data. The
achieved bit error rate is less than 10–7, but now throughput and delay may vary
depending on transmission quality.
Using transparent and non-transparent services, GSM specifies several
bearer services for interworking with PSTN, ISDN, and packet switched public
data networks (PSPDN) like X.25, which is available worldwide. Data transmission
can be full-duplex, synchronous with data rates of 1.2, 2.4, 4.8, and
9.6 kbit/s or full-duplex, asynchronous from 300 to 9,600 bit/s (ETSI, 1991a).
Clearly, these relatively low data rates reflect the assumption that data services
will only constitute some small percentage of the overall traffic. While this
is still true of GSM networks today, the relation of data and voice services is
changing, with data becoming more and more important. This development
is also reflected in the new data services (see section 4.1.8).

Tele services:

GSM mainly focuses on voice-oriented tele services. These comprise encrypted
voice transmission, message services, and basic data communication with terminals
as known from the PSTN or ISDN (e.g., fax). However, as the main service is
telephony, the primary goal of GSM was the provision of high-quality digital
voice transmission, offering at least the typical bandwidth of 3.1 kHz of analog
phone systems. Special codecs (coder/decoder) are used for voice transmission,
while other codecs are used for the transmission of analog data for communication
with traditional computer modems used in, e.g., fax machines.
Another service offered by GSM is the emergency number. The same
number can be used throughout Europe. This service is mandatory for all
providers and free of charge. This connection also has the highest priority,
possibly pre-empting other connections, and will automatically be set up with
the closest emergency center.
A useful service for very simple message transfer is the short message service
(SMS), which offers transmission of messages of up to 160 characters. SMS
messages do not use the standard data channels of GSM but exploit unused
capacity in the signalling channels (see section 4.1.3.1). Sending and receiving
of SMS is possible during data or voice transmission. SMS was in the GSM standard
from the beginning; however, almost no one used it until millions of
young people discovered this service in the mid-nineties as a fun service. SMS
Telecommunication systems 99
can be used for “serious” applications such as displaying road conditions, e-mail
headers or stock quotes, but it can also transferr logos, ring tones, horoscopes
and love letters. Today more than 30 billion short messages are transferred
worldwide per month! SMS is big business today, not only for the network operators,
but also for many content providers. It should be noted that SMS is
typically the only way to reach a mobile phone from within the network. Thus,
SMS is used for updating mobile phone software or for implementing so-called
push services (see chapter 10).
The successor of SMS, the enhanced message service (EMS), offers a larger
message size (e.g., 760 characters, concatenating several SMs), formatted text,
and the transmission of animated pictures, small images and ring tones in a
standardized way (some vendors offered similar proprietary features before).
EMS never really took off as the multimedia message service (MMS) was available.
(Nokia never liked EMS but pushed Smart Messaging, a proprietary
system.) MMS offers the transmission of larger pictures (GIF, JPG, WBMP), short
video clips etc. and comes with mobile phones that integrate small cameras.
MMS is further discussed in the context of WAP in chapter 10.
Another non-voice tele service is group 3 fax, which is available worldwide.
In this service, fax data is transmitted as digital data over the analog telephone
network according to the ITU-T standards T.4 and T.30 using modems. Typically,
a transparent fax service is used, i.e., fax data and fax signaling is transmitted
using a transparent bearer service. Lower transmission quality causes an automatic
adaptation of the bearer service to lower data rates and higher
redundancy for better FEC.

Supplementary services:

In addition to tele and bearer services, GSM providers can offer supplementary
services. Similar to ISDN networks, these services offer various enhancements
for the standard telephony service, and may vary from provider to provider.
Typical services are user identification, call redirection, or forwarding of
ongoing calls. Standard ISDN features such as closed user groups and multiparty
communication may be available. Closed user groups are of special
interest to companies because they allow, for example, a company-specific GSM
sub-network, to which only members of the group have access.

No comments:

Post a Comment