Wednesday, May 5, 2010


System architecture

As with all systems in the telecommunication area, GSM comes with a hierarchical,
complex system architecture comprising many entities, interfaces, and
acronyms. Figure 4.4 gives a simplified overview of the GSM system as specified
in ETSI (1991b). A GSM system consists of three subsystems, the radio sub
system (RSS), the network and switching subsystem (NSS), and the operation
subsystem (OSS). Each subsystem will be discussed in more detail in the following
sections. Generally, a GSM customer only notices a very small fraction of
the whole network – the mobile stations (MS) and some antenna masts of the
base transceiver stations (BTS).

Radio subsystem

As the name implies, the radio subsystem (RSS) comprises all radio specific
entities, i.e., the mobile stations (MS) and the base station subsystem (BSS).
Figure 4.4 shows the connection between the RSS and the NSS via the A interface
(solid lines) and the connection to the OSS via the O interface (dashed
lines). The A interface is typically based on circuit-switched PCM-30 systems
(2.048 Mbit/s), carrying up to 30 64 kbit/s connections, whereas the O interface
uses the Signalling System No. 7 (SS7) based on X.25 carrying management data
to/from the RSS.

Base station subsystem (BSS):

A GSM network comprises many BSSs, each
controlled by a base station controller (BSC). The BSS performs all functions
necessary to maintain radio connections to an MS, coding/decoding of
voice, and rate adaptation to/from the wireless network part. Besides a BSC,
the BSS contains several BTSs.

● Base transceiver station (BTS): A BTS comprises all radio equipment, i.e.,
antennas, signal processing, amplifiers necessary for radio transmission. A
BTS can form a radio cell or, using sectorized antennas, several cells (see section
2.8), and is connected to MS via the Um interface (ISDN U interface for
mobile use), and to the BSC via the Abis interface. The Um interface contains
all the mechanisms necessary for wireless transmission (TDMA, FDMA etc.)
and will be discussed in more detail below. The Abis interface consists of 16 or
64 kbit/s connections. A GSM cell can measure between some 100 m and
35 km depending on the environment (buildings, open space, mountains
etc.) but also expected traffic.

● Base station controller (BSC): The BSC basically manages the BTSs. It
reserves radio frequencies, handles the handover from one BTS to another
within the BSS, and performs paging of the MS. The BSC also multiplexes
the radio channels onto the fixed network connections at the A interface.

● Mobile station (MS): The MS comprises all user equipment and software
needed for communication with a GSM network. An MS consists of user
independent hard- and software and of the subscriber identity module
(SIM), which stores all user-specific data that is relevant to GSM. While an
MS can be identified via the international mobile equipment identity
(IMEI), a user can personalize any MS using his or her SIM, i.e., user-specific
mechanisms like charging and authentication are based on the SIM, not on
the device itself. Device-specific mechanisms, e.g., theft protection, use the
device specific IMEI. Without the SIM, only emergency calls are possible. The
SIM card contains many identifiers and tables, such as card-type, serial
number, a list of subscribed services, a personal identity number (PIN), a
PIN unblocking key (PUK), an authentication key Ki, and the international
mobile subscriber identity (IMSI) (ETSI, 1991c). The PIN is used to
unlock the MS. Using the wrong PIN three times will lock the SIM. In such
cases, the PUK is needed to unlock the SIM. The MS stores dynamic information
while logged onto the GSM system, such as, e.g., the cipher key Kc and
the location information consisting of a temporary mobile subscriber identity
(TMSI) and the location area identification (LAI). Typical MSs for GSM
900 have a transmit power of up to 2 W, whereas for GSM 1800 1 W is
enough due to the smaller cell size. Apart from the telephone interface, an
MS can also offer other types of interfaces to users with display, loudspeaker,
microphone, and programmable soft keys. Further interfaces comprise computer
modems, IrDA, or Bluetooth. Typical MSs, e.g., mobile phones,
comprise many more vendor-specific functions and components, such as
cameras, fingerprint sensors, calendars, address books, games, and Internet
browsers. Personal digital assistants (PDA) with mobile phone functions are
also available. The reader should be aware that an MS could also be integrated
into a car or be used for location tracking of a container.

Network and switching subsystem

The “heart” of the GSM system is formed by the network and switching subsystem
(NSS). The NSS connects the wireless network with standard public
networks, performs handovers between different BSSs, comprises functions for
worldwide localization of users and supports charging, accounting, and roaming
of users between different providers in different countries. The NSS consists of
the following switches and databases:

● Mobile services switching center (MSC): MSCs are high-performance digital
ISDN switches. They set up connections to other MSCs and to the BSCs
via the A interface, and form the fixed backbone network of a GSM system.
Typically, an MSC manages several BSCs in a geographical region. A gateway
MSC (GMSC) has additional connections to other fixed networks, such as
PSTN and ISDN. Using additional interworking functions (IWF), an MSC
can also connect to public data networks (PDN) such as X.25. An MSC
handles all signaling needed for connection setup, connection release and
handover of connections to other MSCs. The standard signaling system
No. 7 (SS7) is used for this purpose. SS7 covers all aspects of control signaling
for digital networks (reliable routing and delivery of control messages,
establishing and monitoring of calls). Features of SS7 are number portability,
free phone/toll/collect/credit calls, call forwarding, three-way calling etc. An
MSC also performs all functions needed for supplementary services such as
call forwarding, multi-party calls, reverse charging etc.

● Home location register (HLR): The HLR is the most important database in a
GSM system as it stores all user-relevant information. This comprises static
information, such as the mobile subscriber ISDN number (MSISDN), subscribed
services (e.g., call forwarding, roaming restrictions, GPRS), and the
international mobile subscriber identity (IMSI). Dynamic information is
also needed, e.g., the current location area (LA) of the MS, the mobile subscriber
roaming number (MSRN), the current VLR and MSC. As soon as an
MS leaves its current LA, the information in the HLR is updated. This information
is necessary to localize a user in the worldwide GSM network. All these
user-specific information elements only exist once for each user in a single
HLR, which also supports charging and accounting. The parameters will be
explained in more detail in section 4.1.5. HLRs can manage data for several
million customers and contain highly specialized data bases which must fulfill
certain real-time requirements to answer requests within certain time-bounds.

● Visitor location register (VLR): The VLR associated to each MSC is a
dynamic database which stores all important information needed for the
MS users currently in the LA that is associated to the MSC (e.g., IMSI,
MSISDN, HLR address). If a new MS comes into an LA the VLR is responsible
for, it copies all relevant information for this user from the HLR. This
hierarchy of VLR and HLR avoids frequent HLR updates and long-distance
signaling of user information. The typical use of HLR and VLR for user
localization will be described in section 4.1.5. Some VLRs in existence, are
capable of managing up to one million customers.

Operation subsystem

The third part of a GSM system, the operation subsystem (OSS), contains the
necessary functions for network operation and maintenance. The OSS possesses
network entities of its own and accesses other entities via SS7 signaling (see
Figure 4.4). The following entities have been defined:

● Operation and maintenance center (OMC): The OMC monitors and controls
all other network entities via the O interface (SS7 with X.25). Typical
OMC management functions are traffic monitoring, status reports of network
entities, subscriber and security management, or accounting and
billing. OMCs use the concept of telecommunication management network
(TMN) as standardized by the ITU-T.

● Authentication centre (AuC): As the radio interface and mobile stations
are particularly vulnerable, a separate AuC has been defined to protect user
identity and data transmission. The AuC contains the algorithms for
authentication as well as the keys for encryption and generates the values
needed for user authentication in the HLR. The AuC may, in fact, be situated
in a special protected part of the HLR.

● Equipment identity register (EIR): The EIR is a database for all IMEIs, i.e.,
it stores all device identifications registered for this network. As MSs are
mobile, they can be easily stolen. With a valid SIM, anyone could use the
stolen MS. The EIR has a blacklist of stolen (or locked) devices. In theory an
MS is useless as soon as the owner has reported a theft. Unfortunately, the
blacklists of different providers are not usually synchronized and the illegal
use of a device in another operator’s network is possible (the reader may
speculate as to why this is the case). The EIR also contains a list

Monday, May 3, 2010

GSM....

last post ws about evolution of these technologies....
nw letz discuss something about GSM system in particular.


GSM is the most successful digital mobile telecommunication system in the
world today. It is used by over 800 million people in more than 190 countries.
In the early 1980s, Europe had numerous coexisting analog mobile phone systems,
which were often based on similar standards (e.g., NMT 450), but ran on
slightly different carrier frequencies. To avoid this situation for a second generation
fully digital system, the groupe spéciale mobile (GSM) was founded in
1982. This system was soon named the global system for mobile communications
(GSM), with the specification process lying in the hands of ETSI (ETSI,
2002), (GSM Association, 2002). In the context of UMTS and the creation of
3GPP (Third generation partnership project, 3GPP, 2002a) the whole development
process of GSM was transferred to 3GPP and further development is
combined with 3G development. 3GPP assigned new numbers to all GSM stan-
96 Mobile communicationsdards. However, to remain consistent with most of the GSM literature, this GSM section stays with the original numbering (see 3GPP, 2002a, for conversion).
Section 4.4 will present the ongoing joint specification process in more detail.
The primary goal of GSM was to provide a mobile phone system that allows
users to roam throughout Europe and provides voice services compatible to
ISDN and other PSTN systems. The specification for the initial system already
covers more than 5,000 pages; new services, in particular data services, now add
even more specification details. Readers familiar with the ISDN reference model
will recognize many similar acronyms, reference points, and interfaces. GSM
standardization aims at adopting as much as possible.GSM is a typical second generation system, replacing the first generation analog systems, but not offering the high worldwide data rates that the third generation systems, such as UMTS, are promising. GSM has initially been deployed in
Europe using 890–915 MHz for uplinks and 935–960 MHz for downlinks – this
system is now also called GSM 900 to distinguish it from the later versions. These
versions comprise GSM at 1800 MHz (1710–1785 MHz uplink, 1805–1880 MHz
downlink), also called DCS (digital cellular system) 1800, and the GSM system
mainly used in the US at 1900 MHz (1850–1910 MHz uplink, 1930–1990 MHz
downlink), also called PCS (personal communications service) 1900. Two
more versions of GSM exist. GSM 400 is a proposal to deploy GSM at
450.4–457.6/478.8–486 MHz for uplinks and 460.4–467.6/488.8–496 MHz for
downlinks. This system could replace analog systems in sparsely populated areas.
A GSM system that has been introduced in several European countries for
railroad systems is GSM-Rail (GSM-R, 2002), (ETSI, 2002). This system does not
only use separate frequencies but offers many additional services which are
unavailable using the public GSM system. GSM-R offers 19 exclusive channels
for railroad operators for voice and data traffic (see section 4.1.3 for more information
about channels). Special features of this system are, e.g., emergency calls
with acknowledgements, voice group call service (VGCS), voice broadcast service
(VBS). These so-called advanced speech call items (ASCI) resemble features
typically available in trunked radio systems only (see section 4.3). Calls are prioritized:
high priority calls pre-empt low priority calls. Calls have very short
set-up times: emergency calls less than 2 s, group calls less than 5 s. Calls can be
directed for example, to all users at a certain location, all users with a certain
function, or all users within a certain number space. However, the most sophisticated
use of GSM-R is the control of trains, switches, gates, and signals. Trains
going not faster than 160 km/h can control all gates, switches, and signals
themselves. If the train goes faster than 160 km/h (many trains are already capable
of going faster than 300 km/h) GSM-R can still be used to maintain control.


Mobile services


GSM permits the integration of different voice and data services and the interworking
with existing networks. Services make a network interesting for
customers. GSM has defined three different categories of services: bearer, tele,
and supplementary services. These are described in the following subsections.
Figure 4.3 shows a reference model for GSM services. A mobile station MS is
connected to the GSM public land mobile network (PLMN) via the Um interface.
(GSM-PLMN is the infrastructure needed for the GSM network.) This
network is connected to transit networks, e.g., integrated services digital network
(ISDN) or traditional public switched telephone network (PSTN). There
might be an additional network, the source/destination network, before another
terminal TE is connected. Bearer services now comprise all services that enable
the transparent transmission of data between the interfaces to the network, i.e., S
in case of the mobile station, and a similar interface for the other terminal (e.g.,
S0 for ISDN terminals). Interfaces like U, S, and R in case of ISDN have not been
defined for all networks, so it depends on the specific network which interface is
used as a reference for the transparent transmission of data. In the classical GSM
model, bearer services are connection-oriented and circuit- or packet-switched.
These services only need the lower three layers of the ISO/OSI reference model.
Within the mobile station MS, the mobile termination (MT) performs all
network specific tasks (TDMA, FDMA, coding etc.) and offers an interface for
data transmission (S) to the terminal TE which can then be network independent.
Depending on the capabilities of TE, further interfaces may be needed,
such as R, according to the ISDN reference model (Halsall, 1996). Tele services
are application specific and may thus need all seven layers of the ISO/OSI reference
model. These services are specified end-to-end, i.e., from one terminal TE
to another.

Bearer services:

GSM specifies different mechanisms for data transmission, the original GSM
allowing for data rates of up to 9600 bit/s for non-voice services. Bearer services
permit transparent and non-transparent, synchronous or asynchronous data
transmission. Transparent bearer services only use the functions of the physical
layer (layer 1) to transmit data. Data transmission has a constant delay and
throughput if no transmission errors occur. The only mechanism to increase transmission quality is the use of forward error correction (FEC), which codes
redundancy into the data stream and helps to reconstruct the original data in
case of transmission errors. Depending on the FEC, data rates of 2.4, 4.8, or
9.6 kbit/s are possible. Transparent bearer services do not try to recover lost data
in case of, for example, shadowing or interruptions due to handover.
Non-transparent bearer services use protocols of layers two and three to
implement error correction and flow control. These services use the transparent
bearer services, adding a radio link protocol (RLP). This protocol comprises
mechanisms of high-level data link control (HDLC), (Halsall, 1996) and special
selective-reject mechanisms to trigger retransmission of erroneous data. The
achieved bit error rate is less than 10–7, but now throughput and delay may vary
depending on transmission quality.
Using transparent and non-transparent services, GSM specifies several
bearer services for interworking with PSTN, ISDN, and packet switched public
data networks (PSPDN) like X.25, which is available worldwide. Data transmission
can be full-duplex, synchronous with data rates of 1.2, 2.4, 4.8, and
9.6 kbit/s or full-duplex, asynchronous from 300 to 9,600 bit/s (ETSI, 1991a).
Clearly, these relatively low data rates reflect the assumption that data services
will only constitute some small percentage of the overall traffic. While this
is still true of GSM networks today, the relation of data and voice services is
changing, with data becoming more and more important. This development
is also reflected in the new data services (see section 4.1.8).

Tele services:

GSM mainly focuses on voice-oriented tele services. These comprise encrypted
voice transmission, message services, and basic data communication with terminals
as known from the PSTN or ISDN (e.g., fax). However, as the main service is
telephony, the primary goal of GSM was the provision of high-quality digital
voice transmission, offering at least the typical bandwidth of 3.1 kHz of analog
phone systems. Special codecs (coder/decoder) are used for voice transmission,
while other codecs are used for the transmission of analog data for communication
with traditional computer modems used in, e.g., fax machines.
Another service offered by GSM is the emergency number. The same
number can be used throughout Europe. This service is mandatory for all
providers and free of charge. This connection also has the highest priority,
possibly pre-empting other connections, and will automatically be set up with
the closest emergency center.
A useful service for very simple message transfer is the short message service
(SMS), which offers transmission of messages of up to 160 characters. SMS
messages do not use the standard data channels of GSM but exploit unused
capacity in the signalling channels (see section 4.1.3.1). Sending and receiving
of SMS is possible during data or voice transmission. SMS was in the GSM standard
from the beginning; however, almost no one used it until millions of
young people discovered this service in the mid-nineties as a fun service. SMS
Telecommunication systems 99
can be used for “serious” applications such as displaying road conditions, e-mail
headers or stock quotes, but it can also transferr logos, ring tones, horoscopes
and love letters. Today more than 30 billion short messages are transferred
worldwide per month! SMS is big business today, not only for the network operators,
but also for many content providers. It should be noted that SMS is
typically the only way to reach a mobile phone from within the network. Thus,
SMS is used for updating mobile phone software or for implementing so-called
push services (see chapter 10).
The successor of SMS, the enhanced message service (EMS), offers a larger
message size (e.g., 760 characters, concatenating several SMs), formatted text,
and the transmission of animated pictures, small images and ring tones in a
standardized way (some vendors offered similar proprietary features before).
EMS never really took off as the multimedia message service (MMS) was available.
(Nokia never liked EMS but pushed Smart Messaging, a proprietary
system.) MMS offers the transmission of larger pictures (GIF, JPG, WBMP), short
video clips etc. and comes with mobile phones that integrate small cameras.
MMS is further discussed in the context of WAP in chapter 10.
Another non-voice tele service is group 3 fax, which is available worldwide.
In this service, fax data is transmitted as digital data over the analog telephone
network according to the ITU-T standards T.4 and T.30 using modems. Typically,
a transparent fax service is used, i.e., fax data and fax signaling is transmitted
using a transparent bearer service. Lower transmission quality causes an automatic
adaptation of the bearer service to lower data rates and higher
redundancy for better FEC.

Supplementary services:

In addition to tele and bearer services, GSM providers can offer supplementary
services. Similar to ISDN networks, these services offer various enhancements
for the standard telephony service, and may vary from provider to provider.
Typical services are user identification, call redirection, or forwarding of
ongoing calls. Standard ISDN features such as closed user groups and multiparty
communication may be available. Closed user groups are of special
interest to companies because they allow, for example, a company-specific GSM
sub-network, to which only members of the group have access.

Sunday, May 2, 2010

Telecommunication systems

Letz start with d basics.....
something about telecommunication....

Digital cellular networks are the segment of the market for mobile and
wireless devices which are growing most rapidly. They are the wireless
extensions of traditional PSTN or ISDN networks and allow for seamless
roaming with the same mobile phone nation or even worldwide. Today, these
systems are mainly used for voice traffic. However, data traffic is continuously
growing and, therefore, this chapter presents several technologies for wireless
data transmission using cellular systems.1
The systems presented fit into the traditional telephony architecture and do
not originate from computer networks. The basic versions typically implement a
circuit-switched service, focused on voice, and only offer data rates of up to,
e.g., 9.6 kbit/s. However, service is provided up to a speed of 250 km/h (e.g.,
using GSM in a car) where most other wireless systems fail.
The worldwide market figures for cellular networks are as follows (GSM
Association, 2002). The most popular digital system is GSM, with approximately
70 per cent market share. (This system will be presented in section 4.1.) The
analog AMPS system still holds three per cent, whereas the Japanese PDC holds
five per cent (60 million users). The remainder is split between CDMA (12 per
cent) and TDMA (10 per cent) systems, and other technologies. In Europe
almost everyone uses the digital GSM system (over 370 million) with almost no
analog systems left. The situation is different in the US and some other countries
that have adopted US technology (e.g., South Korea, Canada). Here, the
digital market is split into TDMA, CDMA, and GSM systems with 107 million
TDMA, 135 million CDMA, and only 16 million GSM users (North America
only). While only one digital system exists in Europe, the US market is divided
into several systems. This leads to severe problems regarding coverage and service
availability, and is one of the examples where market forces did not ensure
improved services (compared to the common standard in Europe).
Figure 4.1 shows the worldwide number of subscribers to different mobile
phone technologies (GSM Association, 2002). The figure combines different versions
of the same technology (e.g., GSM working on 900, 1,800, and 1,900 MHz).




The two upper lines in the graph show the total number of users and the predictions
from 1998. It is interesting that no one foresaw the tremendous success of
the mobile communication technology. The graph shows, too, that the time for
analog systems is over and GSM is heavily dominating the current market. GSM,
TDMA, CDMA, and PDC are all second generation systems. It is important to
note that today more people use mobile phone systems than fixed telephones!
The graphs of mobile and fixed users crossed in March 2002.
The following sections present prominent examples for second generation
(2G) mobile phone networks, cordless telephones, trunked radio systems, and
third generation (3G) mobile phone networks. This chapter uses GSM as the
main example for a 2G fully digital mobile phone system, not only because of
market success, but also due to the system architecture that served many other
systems as an early example. Other systems adopted mobility management,
mobile assisted handover and other basic ideas (Goodman, 1997), (Stallings,
2002), (Pahlavan, 2002). While US systems typically focus on the air interface
for their specification, a system like GSM has many open interfaces and network
entities defined in the specification. While the first approach enables companies
to have their own, proprietary and possibly better solutions, the latter enables
network providers to choose between many different products from different
vendors. DECT and TERTA are used, respectively as examples for cordless telephony
and trunked radio systems. One reason for this is their system
architecture which is similar to GSM. This is not very surprising as all three systems
have been standardized by ETSI. The main focus is always on data service,
so the evolution of GSM offering higher data rates and packet-oriented transfer
is also presented. The chapter concludes with UMTS as a prominent example for
3G mobile telecommunication networks. UMTS is Europe’s and Japan’s proposal



for the next generation mobile and wireless system within the ITU IMT-2000
framework. The early phases of UMTS show the evolutionary path from GSM
via GSM with higher data rates to UMTS, which allows for saving a lot of investment
into the infrastructure. Later phases of UMTS development show more
and more the integration of Internet technology that simplifies service creation
and offers a migration path to more advanced networks.
Figure 4.2 shows several development and migration paths for different
mobile telecommunication systems presented in this chapter. The diagram is
divided into the three main multiplexing schemes, FDMA, TDMA, and CDMA.
The figure classifies the technologies into three generations. The first generation
comprises analog systems, which typically rely on FDMA. The first 2G systems
hit the market in the early nineties. In the US D-AMPS was a digital successor of
AMPS, in Europe GSM was developed as a replacement for several versions of
NMT, and PDC was introduced in Japan. All these 2G systems introduced a
TDMA mechanism in addition to FDMA, which is still used for channel separation.
With cdmaOne the first CDMA technology was available in the US as a
competitor to the TDMA technologies. Between the second and third generation
there is no real revolutionary step. The systems evolved over time: GPRS
introduced a packet-oriented service and higher data rates to GSM (but can also
be used for TDMA systems in general), EDGE proposes a new modulation
scheme, and cdmaOne was enhanced to cdma2000 1x offering higher data
rates. These systems are often called 2.5G systems.2 Most, but not all, systemsadded CDMA technology to become 3G systems. Cordless telephone systems
started with CT0 and CT1, became digital with CT2, and ended in Europe in the
fully digital standard DECT. This standard has even been chosen as one of the
candidates for a 3G system (IMT-FT).
While the number of different systems might be confusing, there are some
“natural” development paths. Most network providers offering GSM service
today will deploy UMTS, while cdmaOne users will choose cdma2000 for simpler
migration. The reasons for this are quite simple. With the introduction of GPRS
in GSM networks, the core of the network was already enhanced in a way that it
can be directly used for UMTS with the radio technologies UTRA FDD and UTRA
TDD. A similar path for evolution exists for TD-SCDMA, the Chinese proposal
for a 3G system (which has been integrated into UTRA TDD). With some simplification
it can be said that UMTS mainly adds a new radio interface but relies in
its initial phase on the same core network as GSM/GPRS. Also for cdmaOne the
evolution to cdma2000 technologies is quite natural, as the new standard is
backward compatible and can reuse frequencies. Cdma2000 1x still uses the same
1.25 MHz channels as cdmaOne does, but offers data rates of up to 153 kbit/s.
The cdma2000 3x standard uses three 1.25 MHz channels to fit into ITU’s frequency
scheme for 3G. However, this standard is not pushed as much as the
following enhancements of cdma2000 1x. These enhancements are:
● cdma2000 1x EV-DO (evolution-data optimized, also known as high data
rate (HDR), some call it data only) promising peak data rates of 2.4 Mbit/s
using a second 1.25 MHz channel; and
● cdma2000 1x EV-DV (evolution-data and voice) aiming at 1.2 Mbit/s for
mobile and 5.2 Mbit/s for stationary users.
Cdma2000 1x EV-DO was the first version of cdma2000 accepted by the ITU as
3G system.

Start....

This is my second blog.....I have discussed various technologies in my previous blog.
This one is specially for GSM technology...
Doing Msc-IT i had a subject called Mobile communication....probably one of the most interesting topic..
So here i will discuss all the aspects of GSM technology...from its basics to 2G to new 3G technology......